Audi 80/Avant
The description
Engines
System of release of the fulfilled gases
Cooling system
Fuel tank and the fuel pump
The air filter and intake channels
Injection system
Coupling
Transmission and transmission
Suspension bracket and steering
Brake system
Antiblocking system of brakes
Wheels and tyres
body electrosystem
Ignition system
Illumination
Signalling devices
Devices and auxiliary devices
Heating and ventilation
- Body elements
Forward bumpers
Forward part of the car
Cowl
Wings
Молдинги
Doors
External rear-view mirrors
The forward and back has flown down
Cover of a luggage carrier at a sedan
Back door of the versatile person
Back bumper
The sdvizhnoj hatch
Procleaning of apertures for a water drain
The control of anticorrosive protection of the bottom of a body
Salon
Seats
Search of malfunctions
Specifications
|
Молдинги
Removal of lobbies moldingов
|
|
- Молдинг on a forward wing: to remove facing of a wheel niche.
- From the interior of a wing to turn on шестигранную a nut.
- To shift molding back and to remove from a wing.
- Молдинг on a lateral part behind (a back wing): to warm up molding the hair dryer to temperature approximately 40С.
- Then to take out molding from a fixing percussion cap the screw-driver which has been wrapped up in a rag.
- At installation to insert molding in fixing клипсу and in addition to paste (for example as it is described more low or in the help).
- Молдинги on doors: to disconnect an overlay from a glutinous layer.
- In most cases it can be made, only heating molding the hair dryer approximately to temperature 40С, but also in this case more often the overlay does not manage to be removed the intact. Therefore it is necessary to take care of the new.
- If at your car a new varnish covering: to clear a place on a door where it will be pasted molding, gasoline and удалителем silicone.
- Otherwise on a door with an old covering. You should remove the glue rests, having left about 1 mm of a thickness. This rest is necessary as a basis for new клеющего a material.
- Watch thus not to damage a varnish covering.
- To clear a place on a door where it will be pasted molding.
Plastic parts in the field of gluing to wipe cleaner D 009 400 01 and to wipe dry.
- Metal (only in case on metal a new varnish covering) and plastic elements of a body to cover in the field of gluing by a first coat. For metal parts to apply праймер D 009 200 02, to plastic D 009 600.
- To put on an underside moldingов клеющий hermetic AKD 476 KD5 05 from PUR – in the middle moldingа the layer suffices gluing thickness of 4 mm.
- To put molding to a door, to correct and densely to press in a gluing place – especially the ends.
- Hardening time at 20С: 4 hours.
|
|
|
|
The help: if the procedure written under instructions Audi seems too difficult, it is possible to arrive as follows: to put a thick layer on an underside moldingа transparent silicone hermetic. To press molding on the cleared overlay of a door and to clean superfluous hermetic. Before hermetic drying (about one day) to fix molding клеющей a tape. In this case molding keeps though and not so it is good, as serial, but nevertheless quite maintains an automatic sink. |
The bottom protective overlay
On a bottom edge of doors, and also by adjoining metal parts on the corresponding version of the car there passes a thin protective overlay. More low the removal plan.
|
|
- The parts of an overlay which are on forward wings and on back lateral parts, are pasted. Removal and installation are described in section Removal moldingа.
- To disconnect from moldingов on doors forward and back tips and, at an open door, to remove molding from a percussion cap to (pull out).
|
|
|
|